LED Fixture DMX Controller

1.This unit is a standard DMX 512 controller. 2.There are max 9 LED fixtures can be controlled. 3.Each fixture is up to 6/7 CH

INTRODUCTION:

    

This unit is a standard DMX-512 controller which has 54 or 63 channels output.                                                                                There are maximum 9 LED fixtures can be controlled and each fixture is up to 6-7 DMX channels.  In order to control different brand of LED fixtures there is a fixture library which has 9 kinds of DMX channels set up.  There are 9 programmable chases for user and each chase has up to 50 scenes.    Furthermore, there are 8 preset patterns are corresponding to different LED fixture.  After you finish you chase you can auto running, sound control or manual control them.    In the meantime you can control output, speed, fade and strobe.

SELECT DMX CHANEEL MATCHED TO YOUR FIXTER FROM FIXTURE LIBRARY

According to your fixture you should select one of DMX channel set up from fixture library then you can control you fixture well.

Press and hold up EDIT 3 seconds then LED will flash which means the unit is in PROGRAMING.                                                    Now press FIX1 and FIX2 at same time STEP display will show “L0-7”.                                                                                               Then you can select “L0” to “L7” to corresponding to your fixture.                                                                                                         Now you can use slider of channel to check up your fixture. If it is right you can exit the selection of DMX channel set up.   Press and hold up FIX1 and FIX2 in the meantime then you will see STEP and PROGRAM display will flash 3 times which means it exit. Or you can push EDIT 3 seconds to exit.

 Operation:

1. Enter programming

There are 9 programmable chases for user. Before you want to programming you should select which program you will write to. Please push EDIT to select Program display NO.: 1 to 9. After you confirm then press and hold EDIT 3 seconds EDIT LED will flash which means it is in programming. STEP display show present SCENE NO.: 1-50.

2. Record scene:

Press FIX button 1, then you can adjust output for projector till it show good effect which you want to get then press FIX2 to adjust effect. Repeat upper steps till you finish the FIX9. Then push INSERT and

INSERT led will light up then press INSERT again now STEP and PROGRAM display and LED will flash 3 times which means one step of scene have been written in chases and STEP display increase one step. Now you can repeat upper steps to write next scenes until SETP display show 50 which means it is last scene for the chase.

3. Delete one scene

First press PROGRAM to select which chase you will want to change. Then press DELETE and DELETE LED will light up. Now you can press UP/DOWN select which scenes you will want to delete. Then press DELETE now STEP and PROGRAM display and led will flash 3 times which means you delete this scene and STEP cut down one step.

4. Delete one program

First press PROGRAM to select which chase you want to delete. Then press and hold up EDIT and DELETE button at same time now STEP will show “AL”, then press DELETE button again STEP and PROGRAM display and LED will flash 3 times which means this program had been deleted.

5. Insert one scene

First press PRGORAM to select which program you will want to do. Then push INSERT button and INSERT LED will light up then you push UP/DOWN to select after which step you want to insert. Then adjust output then push INSERT again STEP and PROGRAM and LED will flash 3 times which means you have insert one step. And SETP display shows increase one step.

6. Modification one scene

Press and hold INSERT + DELETE at same time INSERT led and DELETE led will light up. Press UP/DOWN to select which scene you will want to amend. Then adjust output then press INSERT again STEP and PROGRAM and LED will flash 3 times which means you have changed the scene and saved.

7. Exit programming

Press EDIT 3 seconds LED will light off which means Exit Programming.

Running Program :

1. Auto running

After exit programming press EXIT to select which program you will want to be running. Then press AUTO button and corresponding led light up which means it is in auto running. Now you control MASTER, SPEED, FADE TIME and STROBE.

2. Sound running

Same operation is as AUTO. Just select SOUND button.

3. Manual operation

Same operation is as AUTO. Select different FIX to adjust output.

Running present patterns:

Press EDIT button until PROGRAM show “0” and now SETP show “P1” –“P8”. Then push UP/DOWN to select P1- P8, then you can select different running mode.

Technique data:

Power input: DC9V 500mA

DMX interface: XRL 3P

DMX Channels: 54-63 Channels

Dimensions: 29X15X7cm

Weight: 1.3kg

LED Fixture DMX Controller